How To Spray Walls Without Hitting Ceiling – Best Guide

Well, in this article I will Guide You How To Spray Walls Without Hitting Ceiling out the steps including keys tips to make sure your walls ended up beautifully without affecting your ceiling. Let’s get started!

Preparations

Walls need to be cleaned of every scrap of paint or debris. Getting that first coat ready is always important. After the first coat, you can start letting it dry. And if you have ever painted ceilings before, you will know that when they are not dry, they are extremely difficult to paint.

So when they are dry, you will need to start on the second coat. There are a few tricks to getting them to dry quickly enough. A good tip is to stack a few rugs on top of your walls. If you are spraying from the ceiling, try to get yourself a good overhead perch. In addition, for ceilings around 2.5 meters high, you should use a drop sheet.

Once you have your ceilings and walls cleaned, it’s time to cover it with that first coat. Follow the steps below to ensure that you don’t skip any steps.

ALSO READ: How to Fix Paint Roller Marks After Drying

Wall Selection

how to spray walls without hitting ceiling

Before you start planning the wall paintings you need to figure out how high the ceiling will be. This is essential for getting a beautiful look in the place. What is the height of your ceiling? Think about the number of meters above the floor.

You can use the measurement found on a wall chart. Just keep in mind that this is not the actual measurement. Make sure that there is a wall close to the ceiling that you can spray paint on. This is a great time to get an overall look and feel for the room. If your ceiling is not near the floor you can consider using flat ceiling and insert 12 inches between 2 bricks. For proper space utilization you can cover the brick wall with ceiling paint.

Safety

Paint a wall for the first time on a freshly washed surface, don’t you know, eh? Make sure that the surface is dry or all your efforts will just go in vain. Never paint a wall if you’re not sure of the integrity of the surface. Do not use any substances that could slip or drip into the paint. A thin film of water might be a problem,

so wait till it dries before you start spraying. Spray on a small area and then wipe with a clean dry cloth so that the surface dries before applying the paint to the rest of the wall. Use the proper applicator to apply the paint. A foam brush should not be used for applying paint to the wall as it causes faster growth of paint particles and cause more spots. Also, you can’t clean it with soap and water afterwards, the foam brush can’t do that job.

Tools


You are going to need a small paint gun, or pressure washer with a 5-gallon bucket and a wall brush. Step 1 Make sure you have a clear spot to start spraying. Sometimes, it is advisable to lay down a tarp in a calm environment (around midnight, after a late-night with friends) to test the operation of your gun.

Step 2 The spray gun should spray precisely at 15 feet away from you. A lot of pressure should not be applied to the wall. The same goes for the bucket. When the bucket reaches the specified pressure, a “piss streak” is formed on the wall. When the spray hits the walls, you can see a light green color of the paint. You can ignore the “piss streak” but only when you have finished the wall. When the pressure is released, the paint dries quickly.

Preparing the wall for painting

1. Take off all the rugs and furniture from the wall. 2. Wash the wall using cold water. 3. Apply a thin coat of water-based primer. Let it dry completely. 4. Once the primer is dry, apply a second coat of paint to the wall. 5. Let the paint dry completely. 6. If the wall isn’t fully dry, put a thin layer of sanding tape on the dry paint so it won’t bleed when you apply the next coat. 7.

Remove the tape. 8. Let the wall dry completely. 9. Remove the tape. 10. If the wall is still not fully dry, apply another thin coat of water-based primer. Let it dry. 11. Apply a thin coat of paint and let the paint dry. 12. If the wall still isn’t fully dry, apply another layer of paint. 13. Put a thin layer of tape. 14. Let the wall dry. Finishing the painting 15.

Painting the walls

how to spray walls without hitting ceiling

1. Masking tape Painting should start with this process as it protects the ceilings. You can use masksing tape in a rectangular size at both the top and bottom to cover the 2 most exposed areas. 2. Clean Clean the walls in a decent way to prevent any dust from leaving the area and settling on your ceiling. Clean the walls, then tape. 3. Painting Take out your masking tape and start painting the room. Use either soft or “hot-melt” semi-gloss.

I have used both and it’s up to you. Make sure you spray the paint through the wetwall, not around the entire drywall. Make sure you use a roller instead of paint brush because the roller will be safer to use as there is no way paint can splatter on you or the floor and ceiling. Do not use a small, wetwall paint.

ALSO READ: How To Get Rid Of Roller Marks When Painting

Conclusion

Before using any of these solutions, check with your landlord to see if you need to make any additional construction to the area. If you are having trouble keeping it clean and painting it is too cumbersome, then it might be time to find a solution to your dilemma.

This article has been written by Bisma sheikh. She is an experience content writer with 4 years of experience. [email protected]